indentations

英 [ˌɪndɛnˈteɪʃənz]

美 [ɪnˌdɛnˈteɪʃənz]

n.  缺口; 凹陷; 凹痕; 行首缩进; 行首空格; 造成凹陷(或缺口); 将行首缩进
indentation的复数

柯林斯词典

• 行首缩格,行首留空格
  Anindentationis the space at the beginning of a line of writing when it starts further away from the edge of the paper than all the other lines.
• N-COUNT 凹口;缺口
  Anindentationis a shallow hole or cut in the surface or edge of something.
  1. Using a knife, make slight indentations around the edges of the pastry.
     用刀子绕馅饼边沿刻小锯齿。

双语例句

• The varying distance between the microhardness indentations at the blanks of the cracks as a function of applied loads could be monitored to determine the crack opening displacements near the crack tip, which were used to obtain the crack opening load.
  通过测量裂尖后两岸显微硬度压痕随裂纹张开闭合的距离变化，建立了缺口根部角裂纹裂尖附近的裂纹张开位移和载荷的关系，以此确定裂纹的张开应力。
• Watch out for the effects that the spacing between borders and paragraph area produces on indentations and tabulations.
  注意由于缩进或者表格在边框和段落区域之间产生的间隔的影响。
• The endothelium of the superficial cortical arteries was smooth but there were indentations of cell nucleus on it.
  皮质浅动脉：口径细小，内皮光滑，可有细胞核压迹。
• Protected with battlements or parapets with indentations or embrasures for shooting through.
  用锯齿状的和有可以射击的枪眼的城垛、胸墙保护。
• A new experimental measurement of residual stresses around Vickers ′ indentations on the surface of the SiC/ Al 2O 3 nanocomposites is proposed with the aid of a Raman microprobe.
  提出了用拉曼显微镜测试SiC/Al2O3纳米复合材料表层V氏压痕周围残余应力的新方法。
• Not even the long rows of windows and stores, the indentations of the chimneys, and the roofs, and the vague reflections, which are cast back by the wet and muddy pavements, were visible.
  甚至连一排排一层层的窗户、犬牙交错的烟囱和屋顶、泥泞路面的微弱反光也都看不见。
• Please note that the extracts are organized in a quasi-outline format, with indentations that expound on preceding notes.
  请注意，该提取物的组织是一个准纲要格式，与凹入即阐述前款纸币。
• Marked by irregular projections and indentations on the edge or surface.
  平顺的没有破裂、凹痕，高低不平或其它参差状态的；平滑的。
• These products may have indentations, ribs, grooves or other deformations produced during the rolling process ( reinforcing bars and rods).
  这类产品可带有在轧制过程中产生的凹痕、凸缘、槽沟或其他变形（钢筋）。
• Xtrace: iprint= awt activates method trace and set the output to stderr with indentations.
  iprint=mt激活方法跟踪并将输出发送到stderr，进行缩进。